Mk5 Dry Abrasive Kit
  Equipment Included:
Mk5 Abrasive Injector Head, 10 metres x 5/8" Sandblasting Hose and Sand Poker.
The Mk5 Dry Abrasive Injector Kit operates on the Venturi principle in the same way as the Mk1A Injector Kit, but uses a single high velocity pencil jet and a ceramic nozzle in place of the ring jet. In addition to the standard ceramic head, a stainless steel Mk5 head is available fitted with a tungsten carbide nozzle for use with Flowplant's unique underwater blasting unit for diving applications.
Technical Information:
Max Pressure: 700 Bar (10,000psi)
Part Number: 023-013
Wet Abrasive Blast Kit
The Wet Abrasive Blast Unit is the most advanced of Flowplant's abrasive blasting range giving greater control over the depth of cut than conventional shot-blast equipment. The unit can be used with a number of units with applications from removing graffiti from brick walls or leached anti-fouling from ship's hulls without damaging the surface below.
The system consists of a hopper trolley where the abrasive is mixed with water to form the abrasive slurry. The slurry is then pulled through to the jetting head using a Venturi boost system mounted on the side of the hopper.
Ball Jets
 Small ball jets have a ¼" bspm hose fitting, large ball jets have a ½" bspm hose fitting.
Small Ball Jets:
056 - 590: 3 Rear Jets (30º)
056 - 592: 4 Rear Jets (30º)
056 - 593: 6 Rear Jets (30º)
056 - 591: 3 Rear Jets (30º), 1 Forward Jet (180°)
Standard Drain Jets
 Standard drain jets have a ½" bspm hose fitting, and come with either 30º or 45º rearward facing jets.
Standard 30º Drain Jets:
056 - 580: 3 Rear Jets
056 - 582: 4 Rear Jets
056 - 584: 6 Rear Jets
056 - 586: 8 Rear Jets
056 - 581: 3 Rear Jets, 1 Forward
056 - 583: 4 Rear Jets, 1 Forward
056 - 585: 6 Rear Jets, 1 Forward
Standard 45º Drain Jets:
336 - 001: 3 Rear Jets
336 - 003: 4 Rear Jets
336 - 005: 6 Rear Jets
336 - 007: 8 Rear Jets
336 - 002: 3 Rear Jets, 1 Forward
336 - 004: 4 Rear Jets, 1 Forward
336 - 006: 6 Rear Jets, 1 Forward
High Efficiency Drain Jets
 High efficiency drain jets are suitable for use in both drains and sewers, due to their ability to withstand higher flow rates than standard drain jets. The jets are honed at a 30º angle, and can be ordered with either a ½" or ¾" bspm hose fitting. A rotary Screma Jet can also be fitted to HE drain jets.
High Efficiency Drain Jets:
056 - 670: 3 Rear Jets
056 - 672: 4 Rear Jets
056 - 673: 6 Rear Jets
056 - 674: 8 Rear Jets
056 - 671: 3 Rear Jets, 1 Forward
056 - 246: HE Drain Jet c/w Rotary Screma Jet
Desilting Jets
 Plough jets are designed to sit on the bottom of the drain or sewer, flushing out silt and loose deposits that have settled there. Small plough jets (with a ½" bspm hose fitting) are suitable for drains up to 6", whereas large plough jets (with a ¾" bpsm hose fitting) are suitable for larger diameters.
Small Plough Jets:
056 - 044: Plough Jet c/w 2 Fan Jets (30º Rear)
056 - 605: Neolith Plough Jet c/w 2 Fan Jets (30º Rear)
Large Plough Jets:
056 - 042: Plough Jet c/w 4 Fan Jets (30º and 45º Rear)
056 - 604: Neolith Plough Jet c/w 4 Fan Jets (30º and 45º Rear)
Nozzles & Jets
By changing the shape, size or type of nozzle fitted to a gun, the pressure and jetting profile can be easily changed. Fans jets are used for most general jetting applications, pencil jets offer a more concentrated profile and are ideal for detailed work where the jet needs to be concentrated on a small area, and general surface work can be sped up by using a rotary nozzle.
15º Fan Jet
Jet Angle: 15º
Fitting: ¼" bspm
Part Number: Various
High Velocity Pencil Jet
Jet Angle: 0º
Fitting: ¼" bspm
Part Number: Various
P&A Spinning Nozzle Rotary
Fitting: 3/8" bspm
Part Number: 056 - 326
Turbo Jet Nozzle
 Description:
This rotary jet has rounded guides to assist it negotiating bends and to avoid becoming jammed in the pipe. The Turbo Jet can be fitted with extension jet arms and mounted to a centralising device if required.
Technical Details:
Outside Diameter: 65mm
Fitting: ½" bpsf
Pipe Size: 70 - 100mm (without extension arms)
Max Working Pressure: 700 Bar
Working Flow: 55 - 136 litres/min
Part Number:
056 - 322: Rotary Turbo Nozzle with 2 x 15º fwd jets
056 - 323 Rotary Turbo Nozzle with 2 x 15º rear jets
Rotary Jet Extension Arms
Description:
Designed to operate with the adjustable centraliser and either centraliser screma jets or the rotary turbo jet to increase the size of the tubes that can be cleaned effectively. One O Ring is needed per Extension Arm.
Part Number:
056 - 278: 25mm Extension Arm
056 - 260: 35mm Extension Arm
056 - 279: 50mm Extension Arm
056 - 280: 75mm Extension Arm
013 - 278: 'O' Ring for Jet Extension Arms
Aquaspin Jets
 Low Pressure Spinning Jets are available in 28mm, 40mm, 60mm and 100mm diameters. 28mm-60mm jets can work to 500 Bar (7,250psi), and the 100mm nozzles can work to 250 Bar (3,600psi).
"RGS" Rotary Radial Nozzle
4 x 90º Cleaning Jets and 3 x Thrust Jets
6446: 28mm OD, ¼" bsp Connection Thread
6453: 40mm OD, ½" bsp Connection Thread
"HRH" Rotary Half Radial Nozzle
4 x 45º Rear Jets
6448: 28mm OD, ¼" bsp Connection Thread
6456: 40mm OD, ½" bsp Connection Thread
"HRV" Rotary Radial Nozzle
4 x 45º Forward Jets, 3 x Thrust Jets
6447: 28mm OD, ¼" bsp Connection Thread
6453: 40mm OD, ½" bsp Connection Thread
Rotary Combi Nozzle
2 x 90º Jets and either 2 x 45º Rear Jets or 2 x 45º Forward Jets
6449: 28mm OD, ¼" bsp Connection Thread
6455: 40mm OD, ½" bsp Connection Thread
Tube Cleaning Jets
Female Micro Jets
326 - 000: 45º Rear Jets (various configurations), 1/8" bspf fitting
327 - 000: 90º Side Jets (various configurations), 1/8" bspf fitting
331 - 000: 45º Rear Jets (various configurations), ¼" bspf fitting
331 - 500: Side Jets (various configurations), ¼" bspf fitting Male Micro Jets
320 - 000: Various configurations, ¼" unf fitting
321 - 100: Various configurations, 5/16" unf fitting
056 - 085 / 056 - 095: Harben Type (various configurations), 5/16" unf fitting
 Rotary Screma Jets
Rotary Screma jets all have a 16mm outside diameter, 1/8" bspf connecting thread, and are suitable for 20-100mm tube sizes. Max working pressure is 700 Bar.
056 - 206: 2 x 45º Rear Jets
056 - 207: 2 x 90º Jets
056 - 218: 2 x 45º Forward Jets
056 - 286: 1 x 45º Rear Jet, 1 x 45º Forward Jet
Jet Leaders for Screma Jets
Jet Leaders fits into Screma Jets to give added thrust and utilise excess water which will not flow through Screma Jet.
056 - 245: 2 x Rear Jets, 1/8" bspm x 1/8" bspf fitting
Screma Jet Hose
Screma Jet Hose has ¼" bspf x 1/8" bspm fittings.
055 - 158: 20' x ¼" Screma Jet Hose (MWP350 Bar)
055 - 160: 20' x 3/16" Screma Jet Hose (MWP 700 Bar)
S.O. Type Screma Jet
30mm OD, ¼" connecting thread, 35-50mm Pipe Size. MWP 700 Bar. Working Flow 40 - 73 litres per minute. ¼" bspf fitting.
056 - 262: 2 x 45º Fwd Jets, 3 x 180º Fwd Jets.
056 - 263: 2 x 90º Side Jets, 3 x 180º Fwd Jets
056 - 264: 2 x 45º Rear Jets, 3 x 180º Fwd Jets
056 - 265: 2 x 45º Fwd Jets
056 - 266: 2 x 90º Rear Jets
056 - 267: 2 x 45º Rear Jets
056 - 284: 1 x 45º Fwd Jets, 1 x 45º Rear Jets
High Efficiency Drain Jet & Screma Combi
40mm OD, ½" Connecting Thread, 45-100mm Pipe Size. MWP 700 Bar. Working Flow 55 - 100 litres per minute.
056 - 246: High Efficiency Drain Jet c/w 90º Screma Jet Fitted into Cap. ½" bspm
056 - 247: ¼" bspf Cap for High Efficiency Drain Jet to take Screma Jet
056 - 361: ¼" Towing Eye
Tube Cleaning Accessories
Adapters for Lances & Jets
8320: Adapter 1/8" bspf x M8 male
056 - 244: Adapter ¼" bsp x 5/16" unf
056 - 243: Adapter 1/8" bspm x 5/16" unfm
023 - 388: Screma Adapter 1/8" bspm x ¼" bspm
Foot Control Valves
031 - 043: Harben MkII Foot Control Valve. MWP 420 Bar (6,000psi)
033 - 274: Harben Century Foot Control Valve. MWP 830 Bar (12,000psi)
9370: Neolith High Pressure Foot Control Valve. MWP 1,500 Bar (21,750psi)
Miscellaneous Jets
 In addition to the standard range of drain jets, Flowplant also produce some specialist cleaning nozzles.
Bomb Type Drain Jet:
The bomb type drain jet is suitable for higher flows than standard drain jets, and is therefore fitted with a ¾" bspf hose fitting. The jets are drilled at 45º and are available in a number of configurations.
339 - 000: Bomb Type Drain Jet (3R, 3R1F, 4R, 6R)
Talbot Low Impact Drain Jet
As its name suggests, the Talbot jet has been designed in conjunction with Thames Water to reduce the impact on plastic drains whilst cleaning at normal pressures. The Talbot jet has three special elliptical jets drilled at 30º. The jet is fitted with a standard ½" bspm hose fitting.
056 - 616: Talbot Low Impact Drain Nozzle
Bomb Jet:
The bomb jet is designed for cleaning sewers with high flow-rates. The bomb jet is fitted with 8 rearward facing fan jets to provide maximum cleaning power. The bomb jet is supplied with a ¾" bspm hose fitting.
056 - 041: Bomb Jet c/w 8 Rear Facing Fan Jets
Ram Jets:
Ram jets are supplied in two sizes; small with 4 fan jets and a ½" bspm hose fitting, or large with 8 fan jets and a ¾" bspm hose fitting.
056 - 358: Small Ram Jet c/w 4 Fan Jets
056 - 359: Large Ram Jet c/w 8 Fan Jets
Mini Jet Kits
 Mini Jet Kits:
Mini Jet Kits are designed for cleaning small diameter drains and pipes. Two lengths of ¼" hose are available; 20' and 50', each supplied with a small ball jet.
023 - 227: 20' x ¼" Mini Jet Kit
023 - 275: 50' x ¼" Mini Jet Kit
Micro Mini Jets:
For really small diameter pipes, Flowplant produce a range of Micro Mini Jets with a 1/8" bspf hose fitting. These minute jets fit onto 3/16" jetting hose with a max working pressure of 350 Bar. In addition, a spinning jet (350 Bar MWP) is available to fit onto an 11mm OD micro hose.
032 - 601: 20' Micro Mini Jet Kit 300 Bar Max Working pressure
056 - 281: Micro Mini Jet 3 Rear (30º)
056 - 282: Micro Mini Jet 3 Rear Jets (30º), 1 Forward
055 - 159: 20' x 3/16" Micro Mini Jet Hose
N08 - 551: 11mm Combi Spinning Jet (30º Rear)
N06 - 935: 7 metres x 11mm OD Flexible Micro Hose to suit Combi Spinning Jet
Standard Hoverclean
 Description:
The Standard Hoverclean can be powered by any pump which produces a minimum flow of 36 litres/min (8 gpm) at pressures of between 140 Bar (2,000psi) and 350 Bar (5,000psi). Work rates depend on the type of surface being cleaned and the power available but heavily soiled car parks have been cleaned at a rate of 150m²/hour.
Technical Information:
Cleaning Path: 700mm
Max Flow: 68 litres/min (15 gpm)
Max Pressure: 350 Bar (5,000 psi)
Dimensions: 105cm (L) x 72cm (W) x 40cm (H)
Part Number:
032 - 478
Heavy Duty Hoverclean
 Description:
The Heavy Duty Hoverclean is used for applications which require pressures in excess of 350 Bar, and where the operating environment is unsuitable for the Standard Hoverclean. The Heavy Duty Hoverclean is housed within a steel framework and runs off heavy duty castors. Ground clearance is adjustable and on/off control is via a dead-man's handle. Maximum working pressure is 500 Bar (7,000psi).
Technical Information:
Cleaning Path: 700mm
Max Flow: 82 litres/min (18igpm)
Max. Pressure: 500 Bar (7,000psi)
Dimensions: 105cm (L) x 74cm (W) x 17cm (H)
Part Number:
100 - 276
Rotablast Floor Cleaners
Rotablast floor cleaners are heavy duty self-rotating cleaning devices designed to operate in conjunction with units up to 700 Bar and 155 litres per minute. Rotablasts are pushed by an operator on either pneumatic or solid castor wheels with the pressure controlled by a dead-man's handle which diverts the high pressure flow to a low pressure dump line when released. Applications include paint removal from spray paint booths in car and truck manufacturing plants, shipside cleaning, cleaning of aircraft standing areas and rubber removal from the surface of runways, removal of Camrex non-skid surfaces from aircraft carrier decks and oil and grease removal from slipways, forecourts and garages. Rotablast Range
 Description:
Rotablasts are available with 400mm, 600mm and 1000mm cleaning paths, and are all fitted with a tachometer. Maximum working pressure is 700 Bar (10,000psi), and units can cope with flows up to 155 litres/minute (34 gpm).
Part Numbers:
031 - 165: 400mm Rotablast with tachometer
031 - 136: 600mm Rotablast with tachometer
031 - 145: 1000mm Rotablast with tachometer
High Pressure Dump Guns
 Dump guns are fitted with an additional barrel to 'dump' flow when the gun is not on pressure.
Mk II Gun Assembly
Max Working Pressure: 420 Bar (6,000 psi)
031 - 040
Mk II Gun Assembly Stainless Steel
Max Working Pressure: 420 Bar (6,000 psi)
031 - 045
Mk II Gun Choke for multi-gun use
Max Working Pressure: 420 Bar (6,000 psi)
032 - 114
Stainless Steel Manifold for two-gun use
Max Working Pressure: 900 Bar (13,000 psi)
023 - 332
Dump Gun
Max Working Pressure: 1,000 Bar (15,000 psi)
Part Number: 033-317
Dry Shut Guns
Dry shut guns are easily identified by their single barrel, and need an unloader valve fitted to the unit to dump flow when not under pressure. Dry shut guns are most suited to applications where excess water is required to be kept at a minimum, for example inside a warehouse.
Gun I Assembly c/w 900mm Lance.
Max Operating Flow: 40 litres/min (8.8 igpm)
Max Working Pressure: 250 Bar (3,600 psi)
Part Number: 9368
Gun II Assembly c/w 900mm Lance
Max Operating Flow: 80 litres/min (17 igpm)
Max Working Pressure: 400 Bar (5,800 psi)
Part Number: 9404
Safety Clothing
 Wet Suits, Yellow
Small: 061 - 037
Medium: 061 - 025
Large: 061 - 026
Helmet, Visor and Ear Defenders
One Size: 065 - 013
Goggles
One Size: 065 - 033
Rubber Gauntlets
One Size: 065 - 031
Metatarsal Safety Boots
065 - 076 (YELLOW) UHP SIZE 6
065 - 061 (YELLOW) UHP SIZE 7
065 - 060 (YELLOW) UHP SIZE 8
065 - 057 (YELLOW) UHP SIZE 9
065 - 058 (YELLOW) UHP SIZE 10
065 - 066 (YELLOW) UHP SIZE 11
065 - 065 (YELLOW) UHP SIZE 12
High Visibility Coat
One Size: 065 - 045
Safety Leader Hose
 Safety leader hose is brightly coloured, and should be fitted between the end of the jetting hose and the drain jet (or drain jet extension bar where used) to warn the operator that the drain jet is near when rewinding the hose under pressure.
Safety Leader Hose:
055 - 093: 10' x ½" Safety Leader Hose (Orange)
055 - 450: 10' x ¾" Safety Leader Hose (Blue)
Drain Jet Extension
 Drain jet extensions are hollow bars placed between the end of the jetting (or safety leader) hose and the drain jet. The correctly sized bar with prevent the jet turning in the drain and shooting back towards the operator if it hits and obstruction. As a rule of thumb, the drain jet extension should be approximately 1.5 times the diameter of the drain being cleaned.
Drain Jet Extension Bars (½" bspm x ½" bspf):
033 - 085: 9" Drain Jet Extension Bar
033 - 086: 12" Drain Jet Extension Bar
033 - 087: 18" Drain Jet Extension Bar
033 - 088: 24" Drain Jet Extension Bar
Drain Jet Extension Bars (¾" bspm x ¾" bspf):
106 - 057: 9" Drain Jet Extension Bar
106 - 056: 12" Drain Jet Extension Bar
106 - 055: 18" Drain Jet Extension Bar
106 - 054: 24" Drain Jet Extension Bar
106 - 053: 36" Drain Jet Extension Bar
Operation Manuals & Safety Literature
In addition to the manuals listed below, a limited number of foreign language manuals are also available. Please confirm availability and cost before ordering. All Safety Literature is produced by the Association of High pressure Water Jetting Contractors with the exception of the Flowplant "Operators Guide" Cartoon Safety Booklet.
"Safety Code of Practice" Booklet
Published by the Association of High Pressure Water Jetting Contractors
057 - 062
Flowplant "Operators' Guide"
Cartoon Safety Booklet
061 - 259
Other Safety Literature:
Medical Accident Carrying Card (057 - 063)
"Do & Don't" Cautionary Card (057 - 064)
"Do & Don't" Adhesive Pack (057 - 065)
Weils Disease Poster (057 - 061)
Safety Sign c/w Health & Safety Logo (057 - 069)
Safety Sign "Keep Clear HP Water Jetting" (065 - 025)
Safety Sign Frame 600mm x 450mm for use with Safety Sign (065 - 054)
Pump Manuals:
Harben Operators Instruction Manual (061 - 225)
Harben P Pump / Hi Lift Repair Manual (061 - 352)
Harben Century Repair Manual (061 - 357)
Neolith NP180 Plunger Pump Manual (061 - 356)
Service Videos:
Harben P Pump Repair Video
Harben Century Repair Video Hose Feed Guides
Hose feed guides are used to protect the jetting hose from excess wear by preventing it dragging against sharp metal or concrete corners when feeding the hose into a drain or sewer.
Hose Feed Guides:
055 - 147: Tiger Tail Hose Feed Guide
Remote Control Kits
 A new Radio Remote system from Flowplant allows operators to control the jetting unit functions from up to 100 metres away. The “Echo Kit” meets current and impending Water Jetting Association codes of practice and means that the machine can be safely operated with just one man. When the operator selects the radio option from the panel on the machine he can then control the high pressure water stream, engine speed and engine stop functions from a rugged waterproof hand held transmitter pendant. The system works on a coded frequency that stops interference from any other radio source.
Phil Jones, Technical Director at Flowplant comments, “It is vital that the Echo Kit operates in a fail safe manner. The hand held transmitter is in constant radio contact with the machine. Should the operator stray outside the transmitter signal area the high pressure water stream is automatically shut off until he returns to the signal area and re-selects the high pressure water function”
The “Echo Kit” can be fitted to new Flowplant van pack machines or existing units using the standard Yanmar engine. .
Unloaders & Pressure Control Valves
Pressure Control Valves should not be confused with Unloader Valves. There purpose is similar to an adjustable relief valve; they control the pressure and volume discharged by the pump. However, excess flow is recycled or dumped and the pump is under a continuous load, unlike when an Unloader Valve is used. Pressure Control Valves are adjustable throughout their pressure range to suit nozzle size and pump performance. 350 Bar Pressure Control Valve
Description:
This Valve has a maximum working pressure of 350 Bar, and can be hand-adjusted up to its maximum pressure with a flow rate of 90 litres per minute. This type of valve gives complete control over any system giving a choice of pressures (after correct nozzle selection) and minimising pressure losses caused by excessive water volume and hose size.
Technical Details:
Max Working Pressure: 350 Bar (5,000 psi)
Max Flow Rate: 90 Litres/min (20 gpm)
Inlet Connection: ½" bspm
Outlet Connection: ½" bspm
Weight: 3.5 kgs
Part Number:
023 - 157 830 Bar Pressure Control Valve
Description:
This valve has a maximum working pressure of 830 Bar, and is similar to the 350 Bar PCV, but is designed for higher flows and pressures. These Pressure Control Valves are renowned for their reliability and the need for little, if any, maintenance.
Technical Details:
Max. Working Pressure: 830 Bar (12,000 psi)
Inlet Connection: ½" bspm
Outlet Connection: ½" bspm
Weight: 3.5 kgs
Part Number:
022 - 045
Unloader Valves
Unloader Valves are used mainly with Dead Stop Guns, and will control water flow from the pump through to the nozzle when pressure is selected from the gun, or will re-circulate water flow to a header/break tank. Unlike Pressure Control Valves, when in re-circulation mode, the load on the pump is reduced to almost nothing, but pressure between the gun and the unloading valve is locked in the connecting hose. Any excess pressure must be discharged at the end of operation. Although hand adjustment is available in some of the valves below, most valves are pre-set for maximum working pressure and should not be adjusted. Fixed Unloader Valves
UL-180
Operating Pressure Range: 10 - 200 Bar (145 - 2,900 psi)
Flow Rate Range: 5 - 30 litres/min (1.1 - 6.6 gpm)
Part Number: N05352
UL-221
Operating Pressure Range: 25 - 200 Bar (360 - 2,900 psi)
Flow Rate Range: 8 - 50 litres/min (1.7 - 11 gpm)
Part Number: N05353
UL-261/2
Operating Pressure Range: 100 - 280 Bar (1,450 - 4,060 psi)
Flow Rate Range: 12 - 75 litres/min (2.6 - 22 gpm)
Part Number: N05354
UL-300/1
Operating Pressure Range: 40 - 110 Bar (580 - 1,595 psi)
Flow Rate Range: 225 litres/min (50 gpm)
Part Number: 022 - 060
UL-300/2
Operating Pressure Range: 111 - 220 Bar (1,609 - 3,190 psi)
Flow Rate Range: 120 litres/min (26 gpm)
Part Number: N05356
UL-300/3
Operating Pressure Range: 221 - 400 Bar (3,205 - 5,800 psi)
Flow Rate Range: 60 litres/min (13.2 gpm)
Part Number: 022 - 064
UL-500/21
Operating Pressure Range: 50 - 270 Bar (725 - 3,915 psi)
Flow Rate Range: 15 - 130 litres/min (3.3 - 28.6 gpm)
UL-500/31
Operating Pressure Range: 250 - 500 Bar (3,625 - 7,250 psi)
Flow Rate Range: 15 - 225 litres/min (3.3 - 50 gpm)
Unloader Valves with Hand Adjustment
ULH-180
Operating Pressure Range: 10 - 200 Bar (145 - 2,900 psi)
Flow Rate Range: 5 - 30 litres/min (1.1 - 6.6 gpm)
Part Number: EN6033
ULH-180F (Panel mounted)
Operating Pressure Range: 10 - 200 Bar (145 - 2,900 psi)
Flow Rate Range: 5 - 30 litres/min (1.1 - 6.6 gpm)
Part Number: EN6034
ULH-1801 (With syphon injector)
Operating Pressure Range: 10 - 200 Bar (145 - 2,900 psi)
Flow Rate Range: 5 - 30 litres/min (1.1 - 6.6 gpm)
Part Number: EN6035
ULH-221
Operating Pressure Range: 25 - 200 Bar (360 - 2,900 psi)
Flow Rate Range: 8 - 50 litres/min (1.7 - 11 gpm)
Part Number: EN6037
ULH-260
Operating Pressure Range: 40 - 250 Bar (580 - 3,625 psi)
Flow Rate Range: 12 - 100 litres/min (2.5 - 22 gpm)
Part Number: EN6039
Miscellaneous Accessories
Centralisers
Adjustable Centralising Device
This sprung steel guide can be adjusted from 100mm (4") to 230mm (9"). A propulsion jet can be fitted, and the device will accept Turbo Jets and Centraliser Screma Jets. Max Working Pressure is 700 Bar
056 - 242: Adjustable Centraliser Assembly
056 - 241: Adjustable Centraliser Screma Jet
056 - 236: Retro Jet for Adjustable
Heavy Duty Centraliser Device
The heavy duty centraliser can be fitted with various extension arms to suit pipe diameters from 230mm (9") up to 450mm (18"). Spring loading allows for uneven surfaces. Accepts Turbo Nozzles and Screma Nozzles.
057 - 031: 9" - 18" Heavy Duty Centralisers Jet Pumps
 Lightweight and low cost with no moving parts, Jet Pumps operate under the Venturi principle and can pump out dirty water, sludge, effluent and solids at extremely quick rates making it an ideal emergency tool for daily operations. Heliflex discharge hose is not included unless otherwise stated.
Jet Pumps:
032 - 121: 1½" Jet Pump
039 - 001: 2" Jet Pump
012 - 075: 3" Jet Pump
012 - 152: 4" Jet Pump
032 - 427: 1½" Jet Pump & 10 metres of Heliflex Hose
Jump Jet Kits
 Harben Jump Jet Kits can be factory-fitted to Harben P-Type or Century pumps. The device works by dumping the flow from one or more cylinders to produce a pulsing effect. This pulsing pulls the drain jet further than usual down the drain.
Jump Jet Kits:
057 - 022: Harben 'P' Type 3cyl or 4cyl Pump Jump Jet Kit
057 - 023: Harben 'P' Type 6cyl or 8cyl Pump Jump Jet Kit
010 - 027: Harben Century Jump Jet Kit
| 
